|
|
Tri-State ControlSet Actuators from KMC Controls
|
These are repair parts only. For new installations, see the MEP-7013/7063/7713/7763 ControlSet Actuators.
The KMC MEP-7003/7053/7703/7753 ControlSet Actuators are factory mounted onto VEP-5000 Series flanged or butterfly valves, for use in HVAC systems.
These Actuators have Tri-State control signal inputs with an added feedback potentiometer output. The MEP-7053 and 7753 include a fail-safe feature.
The bi-directional motors may be controlled via a SPDT floating thermostat, controller or building automation system. A minimum 150 in-lb. of torque is available on the 7003/7053 and a minimum of 300 in-lb of torque is available on the 7703/7753 over the 94° angular rotation.
A gear disengagement feature allows positioning of the valve/gear train without energizing the actuator. The actuators are protected against overloading and do not require end or limit switches.
The optional fail-safe feature allows selection for the direction of return, and a delay allows full charge before normal operation resumes.
Category: 150 in-lb Electronic Actuator
Category: 300 in-lb Electronic Actuator
|
The KMC MEP-7011/7013/7711/7713 ControlSet Actuators are designed to regulate large control air dampers and valves in HVAC systems. The 7011 and 7711 have 3-wire floating control signal inputs, and the 7013 and 7713 have 3-wire floating control signal inputs with an added feedback potentiometer output. These actuators mount directly to 3/8” up to 1.05” round or 5/16” up to 5/8” square shafts, eliminating the need for expensive and complicated linkage. The bidirectional motors may be controlled via a SPDT floating thermostat, controller, or building automation system. A minimum 150 in-lb of torque is available on the 7000 series and a minimum 300 in-lb of torque is available on the 7700 series over the 94° angular rotation. A gear disengagement feature allows positioning of the damper and/or gear train without energizing the actuator. The actuators are protected against overloading and do not require end or limit switches.
Category: 150 in-lb Electronic Actuator
Category: 300 in-lb Electronic Actuator
|
These ControlSet Actuators are designed to regulate large control air dampers and valves in HVAC systems. Both accept a 2–10 VDC or 4–20 mA control signal input from a thermostat, controller, or building automation system. A 1-5 VDC feedback voltage output is provided which is proportional to the control signal.
These actuators mount directly to 3/8" up to 1.05" round or 5/16" up to 5/8" square shafts, eliminating the need for expensive and complicated linkage. A minimum 150 in-lbs. of torque is available on the 7012 and a minimum 300 in-lbs. of torque is available on the 7712 over the 94° angular rotation.
A gear disengagement feature allows positioning of the damper and/or gear train without energizing the actuator. The actuators are protected against overloading and do not require end or limit switches.
Category: 150 in-lb Electronic Actuator
Category: 300 in-lb Electronic Actuator
|
The KMC MEP-7061/7063/7761/7763 fail-safe ControlSet Actuators are designed to regulate large control air dampers and valves in HVAC systems. The 7061 and 7761 have 3-wire floating control signal inputs, and the 7063 and 7763 have 3-wire floating control signal inputs with an added feedback potentiometer output. These actuators mount directly to 3/8” up to 1.05” round or 5/16” up to 5/8” square shafts, eliminating the need for expensive and complicated linkage. The bidirectional motors may be controlled via a SPDT floating thermostat, controller, or building automation system. A minimum 150 in-lb of torque is available on the 7060 series and a minimum 300 in-lb of torque is available on the 7760 series over the 94° angular rotation. A gear disengagement feature allows positioning of the damper and/or gear train without energizing the actuator. The actuators are protected against overloading and do not require end or limit switches. The fail-safe feature allows selection for the direction of return, and a delay allows a full charge before normal operation is resumed.
Category: 150 in-lb Electronic Actuator
Category: 300 in-lb Electronic Actuator
|
The KMC MEP-MEP-7062/7762 fail-safe ControlSet Actuators are designed to regulate large control air dampers and valves in HVAC systems. Both accept a 2–10 VDC or 4–20 mA control signal input from a thermostat, controller, or building automation system. A 1–5 VDC feedback voltage output is provided which is proportional to the control signal. These actuators mount directly to 3/8” up to 1.05” round or 5/16” up to 5/8” square shafts, eliminating the need for expensive and complicated linkage. A minimum 150 in-lb of torque is available on the 7062 and a minimum 300 in-lb of torque is available on the 7762 over the 94° angular rotation. A gear disengagement feature allows positioning of the damper and/or gear train without energizing the actuator. The actuators are protected against overloading and do not require end or limit switches. The fail-safe feature allows selection for the direction of return, and a delay allows a full charge before normal operation is resumed.
Category: 150 in-lb Electronic Actuator
Category: 300 in-lb Electronic Actuator
|
The KMC TSP-5003/5023 are combination air flow transducer and actuator units designed primarily for variable air volume terminal units controlled via Direct Digital Control (DDC) systems such as KMC’s Digital System. Air flow is sensed by utilizing a single or multi-point differential (velocity) pressure measuring station or pitot tube. Air flow sensing is accomplished utilizing twin platinum resistance temperature detectors. Velocity measurement is maintained at 3% accuracy over the range of 0–3,300 feet per minute (FPM). Each Unit mounts directly to a 1/2" diameter or 3/8" square damper shaft, or a 3/8" diameter shaft (HFO-0011 shaft adaptor required). Damper control is provided by an 18°/ minute or 60°/minute actuator. The actuator is controlled by an SPDT “floating” input. A minimum of 50 inch-pounds of torque is provided. Both minimum and maximum stops are standard to limit the rotation. A gear disengagement feature allows positioning the damper and/or gear-train without energizing the actuator. A 10,000 W, 1/3 W feedback potentiometer is standard. A single, double or triple auxiliary switch may be field installed.
Category: 050 in-lb Electronic Actuator
Category: Electronic Transducers/Transmitters
|
The KMC TSP-6001/6051 are combination air flow transducer and actuator units designed primarily for variable air volume terminal units controlled via Direct Digital Control (DDC) systems such as KMC’s Digital System. Specific applications include slaving from the KMD-6002/6052 in dual duct or tracking applications. Each unit mounts directly to a 1/2" diameter or 3/8" square damper shaft, or a 3/8" diameter shaft (HFO-0011 shaft adaptor required). Damper control is provided by an 18°/ minute or 60°/minute actuator. The actuator is controlled by a three-state analog signal; less than 2 VDC drives CCW, greater than 2.5 VDC drives CW, and 2.25 VDC is idle. A minimum of 50 in-lbs of torque is provided. Both minimum and maximum stops are standard to limit the rotation. A gear disengagement feature allows positioning the damper and/or gear-train without energizing the actuator. The TSP-6001/6051 has an on-board flow-through sensor for use with a single or multi-point differential pressure measuring station or pitot tube. The sensor utilizes twin platinum-ceramic resistance temperature sensors. Velocity measurement is maintained at 3% accuracy over the range of 0 to 3,000 feet per minute (FPM).
Category: 050 in-lb Electronic Actuator
Category: Electronic Transducers/Transmitters
|
|
|
|
TSP-6001, 6051 Air Flow Transducer-Actuator